AKYAPAK USA - Plate Roller - AHS 4-Roll
Akyapak manufactures 4 rolls hydraulic plate bending machines with capacity in thickness from 2 mm to 200 mm and in width from 500 mm to 12000 mm. (from 14 ga. to 8” and in width from 20” to 40ft.)
As well as being reliable, AHS increases productivity with its high speed rolling ability and it overcomes the most challenging bends thanks to its ease of use. Since the plate is pinched during rolling, skidding and slipping of materials are prevented. Thus, more.
In AHS 4-Roll Plate Rolling Machines, one of the side rolls can be used as a squaring roll, thus the plate can be easily and precisely aligned along the roll across the input direction.
In AHS 4-Roll Machines, it is possible to achieve a full cylinder at a single pass because the material can be pinched with the lower-roll during pre-bending and bending. AHS model allows for precise pinching of the plate between upper and lower rolls.
As well as being reliable, AHS increases productivity with its high speed rolling ability and it overcomes the most challenging bends thanks to its ease of use. Since the plate is pinched during rolling, skidding and slipping of materials are prevented. Thus, more.
In AHS 4-Roll Plate Rolling Machines, one of the side rolls can be used as a squaring roll, thus the plate can be easily and precisely aligned along the roll across the input direction.
In AHS 4-Roll Machines, it is possible to achieve a full cylinder at a single pass because the material can be pinched with the lower-roll during pre-bending and bending. AHS model allows for precise pinching of the plate between upper and lower rolls.
AKYAPAK USA - Plate Roller - AHK 3-Roll
In AHK 3-Roll Plate Rolling Machines, every 3 rolls are independently-driven with the reducers and hydraulic motors in the models with a roll diameter of 230mm and over, and in the models with a roll diameter of less than 230mm, the side rolls are driven by a hydraulic motor, reducer + gear and the upper roll is driven by means of chain gear.
Akyapak AHK 3-roll plate rolls allow pre-bending on both sides of the machine without removing the plate. It guarantees excellent feeding by preventing the risk of sliding thanks to the braking system it provides.
Akyapak AHK 3-roll plate rolls allow pre-bending on both sides of the machine without removing the plate. It guarantees excellent feeding by preventing the risk of sliding thanks to the braking system it provides.
AKYAPAK USA - Plate Roller - AHK 3-Roll
Akyapak 3-Roll Initial Pinch Plate Rolls are the best choice for excellent results in thin sheet metal rolling. ASM-S series guarantees a solid structure with its welded-steel body and ensures you to get maximum outputs with minimum investment.
Asymmetric design allows for alignment of the sheet before bending. In this way, the sheet pinched between two rolls maintains its position during bending and guarantees precise bending.
Asymmetric rolling machines ensure you to get excellent results with a single operator thanks to its ease of use feature. It offers full of control at each step of rolling with the control panel and foot switches.
Asymmetric design allows for alignment of the sheet before bending. In this way, the sheet pinched between two rolls maintains its position during bending and guarantees precise bending.
Asymmetric rolling machines ensure you to get excellent results with a single operator thanks to its ease of use feature. It offers full of control at each step of rolling with the control panel and foot switches.
AKYAPAK USA - Angle Roller - APK-H
AKYAPAK offers extensive alternatives on heavy duty profile bending machines as well. Our machines are strong and reliable with their St-52 weld construction body. Minimum flexion causes less deformation, by the help of our machines’ enlarged roll diameters. By the help of big measurements of bearings, durability and high bending momentum can be obtained.
The power of hydraulic cylinders enables to bend the larger parts without difficulty. Practical and universal rollers creates the possibility of easiness for bending various sections, and this feature gives the opportunity of being more powerful and robust.
Akyapak Profile Bending Machines are 3 rolls driven. This feature allows to have a possibility to make the high capacity bending processes real. Secondly, our 3 Rolls Driven machine minimizes the slipping of the materials during the bending process. The two bottom rolls are hydraulically driven and they can move independently with each other.
Therefore, in comparison with the machines which are top roll drive, the features of our machines enhance the ability of operators and give the opportunity to make prebending process on both edges. Side supporters can move towards three directions to reduce the deformations and to facilitate bending processes, especially with angles and spirals.
The power of hydraulic cylinders enables to bend the larger parts without difficulty. Practical and universal rollers creates the possibility of easiness for bending various sections, and this feature gives the opportunity of being more powerful and robust.
Akyapak Profile Bending Machines are 3 rolls driven. This feature allows to have a possibility to make the high capacity bending processes real. Secondly, our 3 Rolls Driven machine minimizes the slipping of the materials during the bending process. The two bottom rolls are hydraulically driven and they can move independently with each other.
Therefore, in comparison with the machines which are top roll drive, the features of our machines enhance the ability of operators and give the opportunity to make prebending process on both edges. Side supporters can move towards three directions to reduce the deformations and to facilitate bending processes, especially with angles and spirals.
AKYAPAK USA - Angle Roller - APK-M
AKYAPAK offers extensive alternatives on heavy duty profile bending machines as well. Our machines are strong and reliable with their St-52 weld construction body. Minimum flexion causes less deformation, by the help of our machines’ enlarged roll diameters. By the help of big measurements of bearings, durability and high bending momentum can be obtained.
On APK101 and APK121, the rolls are driven by a hydraulic motor+planetary gearbox and gears.
On APK101 and APK121, the rolls are driven by a hydraulic motor+planetary gearbox and gears.
AKYAPAK USA - Angle Roller - APK-M
AKYAPAK offers extensive alternatives on heavy duty profile bending machines as well. Our machines are strong and reliable with their St-52 weld construction body. Minimum flexion causes less deformation, by the help of our machines’ enlarged roll diameters. By the help of big measurements of bearings, durability and high bending momentum can be obtained.
On APK61-81, rolls are driven by hydraulic motor+planetary gearbox and gears.
On APK61-81, rolls are driven by hydraulic motor+planetary gearbox and gears.
AM-Disc Master 4TD-1000
The Discmaster 4Td is equipped with two large deburring discs and two edge rounding discs. The discs oscillate continuously over the work piece during the through feed.
See our cost of operations comparison below:
- Deburring and edge rounding in one pass
- All inside and outside edges are processed from all angles and directions
- Available in working widths of 1000mm and 1500mm for smaller parts from 20 x 20mm and for larger parts with widths up to 1500mm
- Uniform wearing of abrasive tools irrespective of the size of the work piece or where it is placed on the conveyor belt. The machine can therefore process wider parts without having to calibrate any tools.
- When processing mixed materials (i.e. steel/stainless- steel) the tools must be changed.
- The four discs on the DiscMaster 4TD can be changed within minutes.
- A large variety of disc tools are available on the market. This keeps tooling costs down and increases the versatility of the machine.
- Low investment, low tooling costs and low operating costs ensure a speedy return on investment.
- Also available as DiscMaster 2TD in 1000 and 1500mm working width.
See our cost of operations comparison below:
ZX Plus-Punching Machines
The new frame with an increase of dimensions enables the machine to operate with higher speeds thus ensuring greater stability and working precision. This machines frame is a normalized nodular cast iron monoblock in Meehanite® with 700N/mm2, designed with FEM (Finite Element Method), punching head directly built into the monoblock frame. In practical terms this means a more robust (no welding points), precise and reliable structure being at the same time compact, hence using less floor space and allowing flexibility in loading different sheet sizes.
Hemsaw Sidewinder A-1
STANDARD FEATURES
- 2 Hold Down Fixtures
- 18″ Exit Support
- Adjustable Clamping Force
- Adjustable Cutting Force
- Adjustable Feed Rate
- Adjustable Main & Feed Vise
- Blade Brush
- Broken Blade Indicator
- Carbide Blade Guides
- Console on Top of Saw – Bi-Function Control
- Flood Coolant System w/ Wash-Down Hose
- Manual Blade Tension
- Manual Guide Arm Adjustment
- Out of Stock Indicator
- Push Button Blade Speed w/ LED Readout
- Safety Guards
- 220V/3PH or 440V/3PH Electrical Motor Requirement – This is Not a Dual Voltage Machine
- 85 PSI, 4-6 CFM Minimum Air Requirement (Equipped w/ Air Filter/Lubricator)
Geka-Hydracrop 80/150
Two hydraulic cylinders ironworker with two simultaneous work stations and five work stations.
2 VERSIONS ON EACH MODEL: S, SD
"S" VERSION
- punching (800 kN power)
- notching
- shear of iron section L (1500 kN power)
- shear of flatbar
- Cut of round and square bars
2 VERSIONS ON EACH MODEL: S, SD
"S" VERSION
- Machines driven by two cylinders.
- 5 work stations, fitted with tools for L , shearing, round and square bars, rectangular notching and punching
- Quick change punch
- Flat bar shearing table with adjustable guides
- 2 simultaneous work stations
- Greater speed backed by a powerful hydraulic unit.
- Special equipment for approaching at reduced pressure and slow speed.
- Precision punching table with X & Y measuring stops.
- Precision notching table with X & Y measuring stops
- Ready for production pack comprising:
- One meter "touch & cut" length stop with fine adjusting.
- Lamp for enhanced vision of cutting zones.
- 10 sets of round punches and dies.
- The same features as the S version, but with a deeper throat for larger plate and sheet metal applications.
